Instructions for using the Paso Panel grape canopy shaded area meter
Mark Battany
Farm Advisor, UC Cooperative Extension
San Luis Obispo and Santa Barbara Counties
mcbattany@ucdavis.edu
Introduction
The Paso Panel is a simple device which is used to measure the midday canopy shaded area of trellised grapevines. This measurement is of interest because it is commonly used to calculate the irrigation crop coefficient (Kc). The midday canopy shaded area can also be useful as a quick non-destructive measure of general vine vegetative growth, for example in evaluating the relative growth due to different fertilizer treatments or rootstocks.
Operation
The theory behind the operation of the Paso Panel is that the electrical current produced by the solar panel is proportional to the amount of direct sunlight striking the panel; thus, as the solar panel surface area is increasingly shaded by the vine leaf canopy, it produces proportionally less current.
There are several important requirements for using the Paso Panel correctly:
- The measurements can only be taken with clear sky conditions. Clouds can be present elsewhere in the sky, but not directly between the solar panel and the sun; any obstructions of the direct sunshine to the solar panel will lead to erratic readings and significant errors. Note that airline contrails disrupt the sunlight in the same way that clouds do.
- Measurements should only be taken near solar noon; in
- The device needs to be held uniformly level, and the solar panel surface needs to be kept free of dust and debris.
- Position the panel as close as possible to the underside of the canopy; the farther away the canopy is from the panel, the greater the possible error.
- Any inadvertent shading of the panel needs to be avoided, such as that caused by the shadow of the person operating the panel. Orient the panel to avoid any such shading.
- The switch which completes the electrical circuit should only be engaged very briefly (about 1 second per reading). This switch short-circuits the solar panel; if it is engaged for excessively long periods in bright sun, the solar panel wiring will burn out, as the solar panel was not designed to be short-circuited like this. Please heed this warning to avoid having to buy an expensive replacement solar panel.
- Under windy conditions, the canopy shaded area will change as shoots and leaves move around. This will cause the current readout on the digital multi-meter to fluctuate accordingly.
Videos
Video: The basics of the Paso Panel
Video: Example measurement in the field
Construction
The Paso Panel consists of three main components:
- A homemade frame with carrying handles
- A PowerFilm™ brand solar panel
- A common digital multi-meter
There are many possible ways to construct a device similar to the Paso Panel; my current design made the best use of my available materials. Your materials, tools and construction skills may make a different design more practical.
The lightweight frame is made from common extruded aluminum available at most hardware stores. For the large sized Paso Panel, the overall length is 8 feet (2.4 m). The frame is 1 foot (0.3 m) wide for all versions. The device can be made in different sizes, to fit different canopies and row spacings; in the photograph below the large sized device is on the left, while a smaller sized device for narrow rows is on the right. The two handles are oriented to place the device at a comfortable height directly underneath the canopy when held by the user. The frame also incorporates a bubble level, to help the operator ensure that the device is held uniformly level for all readings.
The rollable solar panel I used is the PowerFilm™ brand, model number R15-1200 for the larger sized device (this model is now discontinued from the manufacturer). The more recent versions of the PowerFilm™ rollable solar panels have slightly different dimensions than the versions I used when developing the original Paso Panel; your design will therefore have to be adjusted accordingly based on the panels available. For the most current information on these panels, see the manufacturer’s website here.
The digital multi-meter is a commonly available instrument; it is important that the device have the ability to read electrical current of sufficient range. I use a model rated up to 10 amps. The simple wiring diagram of the device is shown below. The two output wires from the solar panel are connected directly to the digital multi-meter, with a pushbutton switch that completes the circuit momentarily. This switch is located in the rear carrying handle.
Wiring diagram. The digital multi-meter is configured according to the manufacturer's instructions to read electrical current (10 amps in this example). If you set up your multi-meter incorrectly, you can easily burn it out!
Downloads:
Spreadsheet for calculating Kc values
Spreadsheet for estimating the number of measurements to make per site
Example data - crop coefficient over season
Example data - canopy size for different rootstocks
Field measurement protocol
Step 1: Take a “Full Sun” reading
Hold the Paso Panel with the same orientation and at the same height as will be used when taking the shaded area readings in the vineyard. Press the switch momentarily and view the electrical current value on the screen of the multi-meter. Record this value.
Step 2: Take the “Shaded” readings
Immediately after recording the “Full Sun” value, begin taking the “Shaded” readings. Hold the panel level and perpendicular to the vine row, directly beneath the leaf canopy, and press the switch to view the electrical current value on the screen of the multi-meter. Take as many readings as necessary to accurately characterize the area of interest. These readings should be done quickly over a period of only a few minutes; if your needs require readings over a longer time period, break the measurement into separate short sequences, each with its own separate “Full Sun” reading preceding the corresponding “Shaded” readings. It is very important to do this, because the “Full Sun” reading is used as a reference value in the calculations, and the magnitude of the “Full Sun” reading will change throughout the day.
To facilitate rapid readings when working alone, use a digital voice recorder with clip-on microphone to record all readings verbally; after finishing the field measurements, play back the recordings while seated at a computer and type the values directly into the spreadsheet which will do the calculations.
Calculations
The calculations are most easily explained in several steps. In practice, the computer spreadsheet listed above will handle all of the calculations.
Step 1: Determine the shaded percentage of the solar panel
Shaded percentage of solar panel = [1 – (Shaded reading/Full Sun reading)] * 100%
(Note that the “Shaded” reading above is the average of all shaded readings for the plot)
Step 2: Determine the shaded percentage of the field
Shaded percentage of field = Shaded percentage of panel * (Panel length/Row spacing)
Step 3: Calculate the crop coefficient
Kc = (0.017 * Shaded percentage of field) – 0.008
Example calculation
Assume that the “Full Sun” reading was 1.7 Amps, and that the ten “Shaded” readings were 1.0, 1.1, 1.1, 1.2, 1.0, 0.9, 0.8, 1.0, 1.1, and 0.9 Amps. The solar panel length is 5.75 ft, and the row spacing is 10 ft. What is the Kc value?
Step 1:
Average of the ten shade readings = 1.01 Amps
Shaded percentage of the solar panel = [1 – (1.01 Amps / 1.7 Amps)] * 100%
Shaded percentage of the solar panel = 41%
Step 2:
Shaded percentage of field = 41% * (5.75 / 10)
Shaded percentage of field = 23.6%
Step 3:
Kc = 0.017 * 23.6% - 0.008
Kc = 0.39
To simplify information, trade names of products and/or company names may have been used. No endorsement of named products and/or companies is intended, nor is criticism implied of similar products and/or companies which are not mentioned.